P-1325T: 1.3 x 2.5 m bed machine
The P-1325T is our 1 300 x 2 500 mm standard-bed machine for shops that cut half-sheet plate without giving up too much floor space. It suits sign work, brackets, panels and general fabrication where plate sizes stay manageable and the machine must be easy to load day to day.
Built for half-sheet work that moves through the shop
The P-1325T is the smallest machine in our standard-bed range, with a 1 300 x 2 500 mm cutting bed and a footprint that fits comfortably into many fabrication shops, sign workshops and maintenance departments. It is built to order in Germiston and configured by option code, so the machine you receive is matched to the way you cut and supplied to suit your work.
This size makes sense where operators work with smaller plate blanks, repeat parts and short runs. It also helps where access is tighter and a larger 1 500 x 3 000 mm or 2 000 x 3 000 mm bed would crowd the loading side or take over too much floor. For many shops this is the machine that covers daily steel work without turning the bay into a plate store.
- Standard bed size: 1 300 x 2 500 mm
- Built to order at our Germiston base
- Configured by option code before build and commissioning
- Suited to sign shops, general fabrication and bracket production
Working area, options and practical cutting limits
The table gives you a nominal 1 300 x 2 500 mm bed, used mainly for half-sheet layouts and smaller nested parts. Final usable area depends on the torch arrangement and the options selected, particularly if you add a flame torch or bed dividers. We discuss that with you before build so the machine lands on site in the form your work actually needs.
Available options for this model include torch-height control, arc-voltage height control or mechanical height control, a flame-cutting torch, a wireless remote pendant, bed dividers, control board choices and the operator stand. Each option affects loading, setup, cutting control and daily use on the floor. For example, a shop cutting mixed plate thicknesses often benefits from height control, while a workshop doing occasional profile cutting in thicker mild steel may want the flame setup added from the start.
- P-THC for torch-height control
- P-THC/ARC for arc-voltage height control
- P-THC/MEC for mechanical height control
- P-FLAME for oxy-fuel flame cutting
- P-REMOTE for wireless pendant control
- P-DIVIDER for bed dividers
- P-BOARD control board options
- P-CONTROL operator stand
If your parts regularly push beyond 2 500 mm in length or need wide nesting across full sheet width, the next bed size usually makes more sense. The P-1325T is meant to stay productive and keep plate handling practical week after week.
Where the P-1325T fits in everyday production
This machine suits shops that cut smaller jobs every day: gussets, base plates, sign letters, infill panels, machine covers, mounting tabs and repair parts. It is also a sensible size for businesses moving from hand-guided cutting to programmed production because loading is straightforward and the machine footprint remains reasonable. On a busy floor that matters more than many buyers expect.
The P-1325T suits half-sheet work, compact production layouts and smaller programmed jobs. Our range covers standard-bed plasma machines built to order in Germiston, with option-based configuration and on-site commissioning. Shops that need very large plate formats or a 3 metre plus gantry usually move to a bigger machine size.
- A good fit for half-sheet plate and compact nesting work
- Useful where the operator loads parts by hand or with light lifting help
- Commonly chosen for signs, brackets, panels and repair components
- Best suited to manageable plate sizes and standard gantry widths
Space, floor and power before delivery
The machine is commissioned on the customer’s floor, so the site matters. You need clear access for offloading and enough working room around the bed for loading, consumable changes and cleaning. A cramped corner tends to slow operators down and makes plate handling harder than it needs to be. Keep one long side open where possible, and leave sensible room at the machine ends for approach and maintenance.
The floor should be level and able to carry the machine, plate and normal workshop traffic without movement. Power provision must match the machine configuration agreed at order stage. We cover these details during the delivery planning process and operator training forms part of commissioning, so the team taking over the machine can start with correct height setting, pierce routines and basic care.
- Allow clear loading access around the 1 300 x 2 500 mm bed
- Prepare a level floor in the machine area
- Confirm site power to suit the chosen configuration
- Keep the bay clear enough for commissioning and training
Daily care that keeps a small machine cutting properly
Regular care keeps a small machine cutting properly. Slat condition, debris removal, cable checks and torch inspection all affect cut quality and machine life. In a shop cutting mild steel every day, a regular cleaning routine saves trouble later. Operators should remove scrap regularly, keep the bed area clear and check that moving parts stay free from dust and dross build-up.
Consumables and torch setup form part of normal production control and should be checked before cut edge quality falls away. If the machine has height control fitted, correct setup is especially important for consistent piercing and travel. Coastal workshops often need to stay stricter with cleaning because humidity works on exposed steel faster, and that can show up in neglected areas sooner than inland shops expect.
During commissioning we show the operator the basic checks that belong to routine use, along with the controls and the option set fitted to that machine.
What to send with your enquiry
When you ask about the P-1325T through our contact form, the most useful starting point is the actual work you want to cut. Plate size, material type, thickness range and whether you need plasma only or plasma with flame all help shape the build. If access into your shop is tight, mention doors, passages and forklift space as well.
It also helps to know whether the machine will stand in a fabrication bay, a sign workshop or a mixed production area. That tells us a lot about loading style, operator movement and the best option code mix. Your town also matters, because delivery and commissioning are handled across Gauteng, KwaZulu-Natal, the Western Cape and the rest of South Africa.
- Your town and installation site details
- Main material types and thickness range
- Typical plate blank size and part sizes
- Whether you want P-THC, P-FLAME, P-REMOTE, P-DIVIDER, P-BOARD or P-CONTROL
- Any access limits at the shop or workshop entrance
- Whether operator training will be for one person or a small team
With those points in hand we can set out a machine that fits the floor and the work and suits your production needs. A short practical brief is better than pages of guesswork.
What our CNC Plasma Machine customers say
Verified Google reviews
Questions we get asked
Is the P-1325T the right size for full sheet plate?
Usually not. The P-1325T is aimed at half-sheet work and smaller nested parts. If your regular production depends on larger plate formats, one of the bigger standard-bed models will be a better fit.
Can this machine be ordered with both plasma and flame cutting?
The machine can be ordered with both plasma and flame cutting where that suits the work. The P-FLAME option can be added during build planning, and we configure the machine by option code before delivery and commissioning.
Do you install this model outside Gauteng?
We build in Germiston and deliver and commission across Gauteng, KwaZulu-Natal, the Western Cape and the rest of South Africa.
Tell us about the job
Send sizes, materials and where you are through our contact form, and we will come back with the practical options.
Open the contact form